DANFOSS EKC 102 A PDF
EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D. EKC B Controller with two relay outputs, extra temperature sensor and digital EN and EN , A2 Weight = g Danfoss can accept no.
|Published (Last):||26 May 2012|
|PDF File Size:||8.28 Mb|
|ePub File Size:||10.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
The relay cuts in when higher temperatures are required remember to cancel defrost functions and compressor functions. Temperature, time, operating environment, parameter codes, alarms and fault codes are displayed Screen read, long-life relay, lower maintenance costs, easy to restore factory settings EKC and are used for Temperature control Compressor control Fan motor control Defrost control Alarm signalling.
Operating status The controller goes through some regulating situations where it is just waiting dancoss the next point of the regulation.
If the function is controlled by a signal at the DI input, the relevant status can be seen here in the menu. All other outputs are Off.
Controller for temperature control – EKC Manual |
No stress and worry Thanks to the integration with cheap returns you can purchase without stress and be sure that the return process will be hassle free. All the mentioned methods can be used at random — if just one them is activated a defrost will be started.
Ceiling Mount Electrical defrosting air cooler high temperature type DL series keep fresh egg. Stopped regulation will give a “Standby alarm”. Defrost The controller contains a timer function that is zeroset after each defrost start.
Drip-off time Here you set the time that is to elapse from a defrost and until the compressor is to start again. The relay is cut out during normal operation and cuts in in alarm situations and when the controller is dead de-energised Refrigeration 2.
The refrigeration and the fans are stopped. This happens when the temperature reaches the upper part of the differential.
When the value is passed, a defrost will start. Check delivery time and costs. Compressor The compressor relay works in conjunction with the thermostat. When copying has started the display returns to o After paying for this item you will be awarded: Lower alarm limit Here you set when the alarm for low temperature is to start. The controller will register when the DI input is activated.
ON-time in minutes Min. EKC D Controller with three relay outputs, two temperature sensors and digital input. All the mounted sensors must be of the same type.
ekd Basic temperature control, precise control Up to 3 relay outputs: EKC for panel mounting and EKC for DIN-rail mounting have been specially developed for control duties in refrigeration plant so that operation, setting and programming are optimised and simplified as much as possible.
The input is not used 1 Status display of a contact function 2 Door function. RA Box type air outlet from side Medium and high temperature scroll rkc condensing unit scroll ZB series. When the controller demands refrigeration it will first cut in the compressor with the shortest operating time. Defrost start can also skc accomplished via contact signals or manual start-up. Providing personal data is voluntary, but necessary for providing a reply. The function delays the interval time d03 by the set number of minutes, but it only does it once, and this at the very first defrost taking place when voltage is connected to the controller.
HVAC Danfoss Electronic Temperature Controller type Danfoss EKC A B for Freezer
For 8 and 9 the time delay is set in A27 10 Case cleaning. Sensors Sair is thermostat sensors. Here you define which: Here are fanfoss messages that may ekd When the compressor is operating it must run for at least x minutes. There will be re-start at 2 K below the setting. Defrost During defrost a —d- is shown in the display.
Relay output 2 can be used for electric defrost or for an alarm function.
Danfoss Temperature controller – EKC 102
Time delay for cooling long alarm delay This time delay is used during start-up recovery timeduring defrost, in the cooling phase after a defrost. When gas defrosting the compressor danflss will be cut in during defrost.
Copying key not correctly mounted 5: You can determine conditions of storing or access to cookie files in your web browser. Thermostatic Expansion Valves flow direction: