JBL 2022H PDF

| | 0 Comments

JBL H (8Ohm). Unavailable. Category of diameter 12 inch / cm; Znom 8 ohm; Weight volume is not set, then delivery by plane is not possible. Brand New JBL H 12″ Aftermarket Recone Kit, 8 ohm. Parts specifications: Cone: 12″ outside diameter, ″ deep, ″ voice coil opening; Voice. Subwoofer JBL H. General specifications: diameter 12 inches, maximum power W. Thiele-Small parameters: frequency of self resonance Fs=75 Hz, .

Author: Jucage Dugul
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Politics
Published (Last): 9 September 2005
Pages: 399
PDF File Size: 2.28 Mb
ePub File Size: 15.15 Mb
ISBN: 495-3-34456-536-5
Downloads: 23838
Price: Free* [*Free Regsitration Required]
Uploader: Mikinos

JBL 2022H 12″ Aftermarket Recone Kit

Basically the K, K, and shared the same magnet structure, including the top plate. Since the taper of the drivers was different I had to cut the new cone at an angle and push it to fit the taper.

With proper processing do you think that it would be a good idea to just stick the in and work it out, while re-coning the One starting point in my confusion I read that someone re-coned a to aincreasing x-maxx how If we knew what the hell we were doing, we wouldn’t call it research would we.

Suprisingly enough it didnt sound too bad last night, but a real re-cone kit is in order. Like every job, it had it’s ups and downs. All times are GMT I was under the thought that the suffix was also something that showed intent or use of the driver eg- a single driver with a 16ohm impedance would be used for a jb, 3 or 4 way system impedance of 8 ohms, but a single 4 ohm driver would be used for a 2 way system impedance of 8 ohms Results 1 to 5 of 5.

  CATERPILLAR 330L PDF

Ie putting a kit in an E and so forth.

However the magnet structures and magnetic energy focusing are different-so you will end up some sort of “half breed”. Another question, can the be reconed to the specs better LF handling?

February 21, Blew a in the monitor older mr series due to a broken handle overexcursion I do have a set of ‘s sitting around but they are the midrange version. Thanks to everyone, good info all around.

JBL H 12″ Woofer Speaker Driver 8 Ohm | eBay

There was a ridge left behind from the old dustcap glue so I had to score the new cone near the former to get it to lay down flat, but once all the pre-fit was done, glue-ing it in wasnt too big of an issue rubber cement Logged If we knew what the hell we were doing, we wouldn’t call it research would we. JBL, The letter following the is used to designate the impedence.

The is also its own, it is an underhung design with a gap depth of 13mm. By that I mean the kits will interchange physically. I’ve been thinking of replacing my ‘s with ‘s down the road a bit and if ‘s can be reconed as ‘s then that could be an option Last edited by maxwedge; at But it has been a few years.

  AKUT INTERNMEDICIN 2012 PDF

The x came in 3 versions listed below.

The is all its own and is bjl less a woofer, it’s dynamite about Hz and above. Is it worth while to recone? Read times Brian Elstro Jr. That is a factor determined by the enclosure and crossover.

Subwoofer JBL H specifications.

It beat itself mbl badly that part of the cone was actually soft to the touch, and very weak. In most cases-similar older JBLS can be reconed “kinda” as different model. I used them as both side fill monitor and full range interchangeably and the has better low end while the is better for vocals.

You will get an enormous reward.

I think they both fall inbetween the “producer” and “reproducer” sound This yields an Xmax of only 0. For a temporary fix I removed an older cone from another torched woofer, removed its suspension and dustcap, carefully removed the dustcap from the jbl and trimmed the glue from the cone as well as I could.